Was this page helpful?
Caution
You're viewing documentation for a previous version of ScyllaDB Monitoring. Switch to the latest stable version.
This document describes steps that need to be done to troubleshoot monitoring problems when using Grafana/Prometheus monitoring tool.
Scylla Manager 2.2 change the default metrics (Prometheus) reporting ports:
For Manager server: from 56090 to 5090
For Manager Agent: from 56090 to 5090
For backward compatibility, Scylla Monitoring Stack 3.5 default configuration reads from both Manager ports, old and new, so you do not have to update the Prometheus configuration when upgrading to Manager 2.2
However, if you configure scylla_manager_server.yml file with the new port, Scylla-Manager dashboard will report all metrics twice.
The easiest way around this is to edit prometheus/prometheus.yml.template and remove the scylla_manager1 job.
Note that for this change to take effect you need to run kill-all.sh followed by start-all.sh.
When running ./start-all.sh a container can fail to start. For example you can see the following error message:
Wait for Prometheus container to start........Error: Prometheus container failed to start
Should this happen, check the Docker logs for more information.
docker logs aprom
Usually the reason for the failure is described in the logs.
Note
Avoid running Docker containers as root.
The preferred way of running the container is using a non root user. See the monitoring Docker post-installation section.
If a container failed to start because of a permission problem, make sure the external directory you are using is owned by the current user and that the current user has the proper permissions.
Note
If you started the container in the past as root, you may need to change the directory and files ownership and permissions.
For example if your Prometheus data directory is /prom-data and you are using centos user
ls -la /|grep prom-data
drwxr-xr-x 2 root root 4096 Jun 25 17:51 prom-data
sudo chown -R centos:centos /prom-data
ls -la /|grep prom-data
drwxr-xr-x 2 centos centos 4096 Jun 25 17:51 prom-data
No data points on all data charts.
If there are no data points, or if a node appears to be unreachable when you know it is up, the immediate suspect is the Prometheus connectivity.
Login to the Prometheus console:
Point your browser to http://{ip}:9090, where {ip} is the Prometheus IP address.
Go to the target tabs: http://{ip}:9090/targets and see if any of the targets are down and if there are any error messages.
Make sure you are not using the local network for local IP range When using Docker containers, by default, the local IP range (127.0.0.X) is inside the Docker container and not the host local address. If you are trying to connect to a target via the local IP range from inside a Docker container, you need to use the
-lflag to enable local network stack.Confirm Prometheus is pointing to the wrong target. Check your
prometheus/scylla_servers.yml. Make sure Prometheus is pulling data from the Scylla server.Your dashboard and Scylla version may not be aligned. If you are running Scylla 3.1.x, you can specify a specific version with
-vflag.
For example:
./start-all.sh -v 3.1
More on start-all.sh options.
Run this procedure on the Scylla Monitoring Stack server.
If the Grafana charts show an error (!) sign, there is a problem with the connection between Grafana and Prometheus.
On the Scylla Monitoring Stack server:
Check Prometheus is running using docker ps.
If it is not running check the prometheus.yml for errors.
For example:
CONTAINER ID IMAGE COMMAND CREATED STATUS PORTS NAMES
41bd3db26240 monitor "/docker-entrypoin..." 25 seconds ago Up 23 seconds 7000-7001/tcp, 9042/tcp, 9160/tcp, 9180/tcp, 10000/tcp monitor
If it is running, go to “Data Source” in the Grafana GUI, choose Prometheus and click Test Connection.
Grafana shows server level metrics like disk usage, but not Scylla metrics. Prometheus fails to fetch metrics from Scylla servers.
Use curl <scylla_node>:9180/metrics to fetch binary metric data from Scylla. If curl does not return data, the problem is the connectivity between the Scylla Monitoring Stack and Scylla server. In that case, check your IPs and firewalls.
For example
curl 172.17.0.2:9180/metrics
Grafana dashboards show Scylla metrics, such as load, but not server metrics such as disk usage.
Prometheus fails to fetch metrics from node_exporter.
1. Make sure that node_exporter is running on each Scylla server (by login to the machine and running ps -ef |gre node_exporter). node_exporter is installed with scylla_setup.
to check that node_exporter is installed, run node_exporter --version, If it is not, make sure to install and run it.
If it is running, use curl http://<scylla_node>:9100/metrics (where <scylla_node> is a Scylla server IP) to fetch metric data from Scylla. If curl does not return data, the problem is the connectivity between Scylla Monitoring Stack and Scylla server. Please check your IPs and firewalls.
While upgrading, you need to upgrade the node_exporter from version 0.14 to 0.17.
If the node_exporter service is not starting it may need to be updated manually.
Check the node_exporter version node_exporter --version if it shows 0.14 check the node_exporter section
in the upgrade guide.
In ScyllaDB, metrics are reported per shard (core) per node. A cluster with a high number of nodes and cores reports an increased number of metrics which might overload the Monitoring system like Prometheus or Datadog. Below is one way to reduce the number of metrics reported per ScyllaDB Node.
By default, node_exporter reports interrupt metrics. You can disable interrupts reporting by editing /etc/sysconfig/scylla-node-exporter and remove –collector.interrupts from it.
No metrics shown in the Scylla Monitoring Stack.
Install wireshark
2. Capture the traffic between the Scylla Monitoring Stack and Scylla node using the tshark command.
tshark -i <network interface name> -f "dst port 9180"
For example:
tshark -i eth0 -f "dst port 9180"
Capture from Scylla node towards Scylla Monitoring Stack server.
In this example, Scylla is running.
Monitor ip Scylla node ip
199.203.229.89 -> 172.16.12.142 TCP 66 59212 > 9180 [ACK] Seq=317 Ack=78193 Win=158080 Len=0 TSval=79869679 TSecr=3347447210
In this example, Scylla is not running
Monitor ip Scylla node ip
199.203.229.89 -> 172.16.12.142 TCP 74 60440 > 9180 [SYN] Seq=0 Win=29200 Len=0 MSS=1460 SACK_PERM=1 TSval=79988291 TSecr=0 WS=128
On this page